![]() The installation process typically takes approximately one hour, allowing you to enjoy the enhanced functionality of your tail lights in no time. Craving greater spacing between individual lamps? Simply install a slower flasher!Įach kit includes two modules, specifically tailored for each side of your vehicle, along with all necessary wiring, connectors, and comprehensive printed instructions. Unlike other products that offer fixed timing or intricate manual adjustments, our modules intelligently detect your car's flasher speed and seamlessly adjust the timing of the 1-2-3 sequence for you. These advanced modules incorporate cutting-edge electronics that automatically synchronize the sequencing speed with your car's turn signal flasher. With this kit, you can effortlessly convert the outer tail light bulb to function as a brake light, turn signal, and tail light, all without the need for any modifications to your tail light housing or socket replacements. Introducing the STS-3TA Sequencer Kit, a revolutionary solution designed to transform the tail lights of your 1993-2002 Firebird or TransAm into a sequential operating system. Many aftermarket kits can not make this claim.1993-2002 Firebird/Trans Am Sequential Taillight Kit XB LED Projector Headlights, Fog Lights, DRL, Tail Lights for Cars & Trucks Elite HID Systems 2Stroke LED Bulbs Custom Mini H1 - D2S - MLED Retrofits. This eliminates the chance of water intrusion which can lead to condensation, fogging and corrosion within the tail light housings. In addition, the kits are specifically engineered to not compromise the waterproof sealing of the tail light housings. This provides the vehicle with the absolute brightest and most noticeable tail light function. The panels will often light up areas that the OEM lighting does not illuminate. Unlike many aftermarket LED panels, our panels are specifically designed to utilize all available lighting area available in the tail light lenses. Ignition must be On to provide sequential flashing.Įach CST kit is uniquely engineered for each application. This allows running illumination and warning flashers when the key is out of the ignition. The exclusive design also allows the tail light panel to perform running light, brake light and emergency flasher functions when the vehicle is not running. This eliminates unnecessary current draw on the battery that can lead to a dead battery over time. When ignition power is Off, the tail light panels do not draw any power from the vehicle. The selection is stored in memory within the onboard controller so every time vehicle is started, the same pattern is used. Selection is performed while panel is powered up so user can observe each pattern until the desired pattern is determined. Each press of the switch steps panel through each of the available patterns. If sequential lighting patterns are desired, then the attached pink wire must be wired to +12 volt ignition power.Ī pushbutton switch on the back or front of the light panel is used to select from any of the pre-programmed sequential patterns. The easy installation requires a quick mounting of the LED lighting panel to the tail light housing or lens, depending on application and plugging in the wired bulb plug(s) into the factory bulb socket(s). Standard Flash Mode: Flashes all LEDs in all panels together with the flasher relay or solid light with brake, mimics light bulb operationĭemonstration Mode: Steps through each sequential pattern cyclically, flashes each sequence 6 times before stepping to the next sequence, then repeats. Tail Light Operational Functions: Turn Signal Light, Brake Light, Running Light and Emergency Flash (not including demonstration and standard flash modes) Number of Sequential Patterns: 11 > Industry First << For LED lighting to function properly, a Low Current Flasher Module must be installed in place of the traditional turn signal flasher module. The kit is designed to work with OEM tail light housing and lenses as well as aftermarket components. There is no separate sequential lighting control module to mount and wire up. In addition, the kit includes a self-contained microprocessor and circuitry to enable a multitude of sequential lighting patterns. This includes low level running light illumination, brake light illumination, turn signal illumination, emergency flash and back-up lighting where applicable. The kits replace all the functionality of the light bulbs they replace. ![]() ![]() ![]() These kits incorporate high efficiency LED lights that increase tail light brightness, reliability and longevity. The Classic Sequential Tail Light (CST) kits are direct retrofit and replacement for incandescent light bulbs in classic vehicles. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |